# Mulching blade 2 week review

**URL:** <https://forum.yarbo.com/t/mulching-blade-2-week-review/6328>\
**Category:** Support & Solutions\
**Created:** [May 30, 2026, 4:45pm UTC](https://forum.yarbo.com/t/mulching-blade-2-week-review/6328 "2026-05-30T16:45:09Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![laudav1285](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.yarbo.com/laudav1285/32/119_2.png) [@laudav1285](https://forum.yarbo.com/u/laudav1285)\
**Post date:** [May 30, 2026, 4:45pm UTC](https://forum.yarbo.com/t/mulching-blade-2-week-review/6328/1 "2026-05-30T16:45:09Z")

</div>

> **[Yarbo cutting/mulching X disc by dhutcheon1285](https://www.thingiverse.com/thing:7350757)**
>
> Refer to my other Yarbo discs and pictures.Print in PETG and anneal for approx. 45 min. at 200 F. for end result of 215 mm. Or reduce in slicer to 215mm if not annealing or using other material. For max seating of heated threaded inserts, install...

After two weeks of using the cross cutting blade, I would hazard to say it works and is sufficiently durable. The combo of metal and annealed plastic PETG blades works surprisingly well.

I did break a few. Mostly by cutting much lower than Yarbo recommends, 1.5 inches and my aluminum disc mount nut had come loose causing a wobble. I tightened them both and it is no longer an issue.

Mulching is pretty good on small sticks and leaves. It might take a couple of passes but it’s better than stock non pro mulching blades.

Happy Printing ( I think I stole that 😉)

Dave

---

<div class="post-metadata">

**Author:** ![hmkb74](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.yarbo.com/hmkb74/32/3254_2.png) [@hmkb74](https://forum.yarbo.com/u/hmkb74)\
**Post date:** [May 31, 2026, 5:01pm UTC](https://forum.yarbo.com/t/mulching-blade-2-week-review/6328/2 "2026-05-31T17:01:17Z")

</div>

Any luck printing two sets for me?

---

<div class="post-metadata">

**Author:** ![laudav1285](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.yarbo.com/laudav1285/32/119_2.png) [@laudav1285](https://forum.yarbo.com/u/laudav1285)\
**Post date:** [May 31, 2026, 5:36pm UTC](https://forum.yarbo.com/t/mulching-blade-2-week-review/6328/3 "2026-05-31T17:36:12Z")

</div>

Yes sir they are ready. $200 USD for two pair and they have nuts/fasteners installed.

Same address?

---

<div class="post-metadata">

**Author:** ![hmkb74](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.yarbo.com/hmkb74/32/3254_2.png) [@hmkb74](https://forum.yarbo.com/u/hmkb74)\
**Post date:** [May 31, 2026, 5:47pm UTC](https://forum.yarbo.com/t/mulching-blade-2-week-review/6328/4 "2026-05-31T17:47:29Z")

</div>

Same address…funds sent

---

<div class="post-metadata">

**Author:** ![laudav1285](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.yarbo.com/laudav1285/32/119_2.png) [@laudav1285](https://forum.yarbo.com/u/laudav1285)\
**Post date:** [May 31, 2026, 6:15pm UTC](https://forum.yarbo.com/t/mulching-blade-2-week-review/6328/5 "2026-05-31T18:15:30Z")

</div>

I see it. Thank you.

I’ll send them out tomorrow or Tuesday.

---

<div class="post-metadata">

**Author:** ![peterfabri18](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.yarbo.com/peterfabri18/32/364_2.png) [@peterfabri18](https://forum.yarbo.com/u/peterfabri18)\
**Post date:** [May 31, 2026, 7:10pm UTC](https://forum.yarbo.com/t/mulching-blade-2-week-review/6328/6 "2026-05-31T19:10:00Z")

</div>

You won’t regret it. They work great

---

<div class="post-metadata">

**Author:** ![laudav1285](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.yarbo.com/laudav1285/32/119_2.png) [@laudav1285](https://forum.yarbo.com/u/laudav1285)\
**Post date:** [May 31, 2026, 7:11pm UTC](https://forum.yarbo.com/t/mulching-blade-2-week-review/6328/7 "2026-05-31T19:11:03Z")

</div>

Fingers crossed 😉😊